Hazardous area classification is the engineering process of mapping out zones or divisions in a facility where flammable gas, vapor, or combustible dust could form an explosive atmosphere, so that only equipment proven safe for that specific risk level gets installed there. Get the zone or the equipment rating wrong and a normal electrical spark, a hot bearing, or a static discharge can trigger a fire or explosion.
Explosions need three things at once: fuel (gas, vapor, or dust), oxygen, and an ignition source. Hazardous area classification removes the guesswork around the first variable by defining, zone by zone, how often and how long an explosive atmosphere is likely to be present. Equipment selection then follows directly from that zone. This is the same logic that underlies other electrical safety disciplines on the plant floor, from arc flash risk assessment to ground fault protection: identify the hazard rigorously first, then engineer the equipment and procedures around it.
IEC 60079-10-1 defines three zones for gas, vapor, or mist atmospheres, based on the likelihood and duration of an explosive atmosphere being present. The European ATEX directive (2014/34/EU) uses the identical zone definitions, since EN 60079 and IEC 60079 have been technically aligned since 2005.
The standard's wording is intentionally qualitative. Some national guidance, such as UK HSE practice, applies rough hour based benchmarks, roughly over 1,000 hours per year for Zone 0, 10 to 1,000 hours per year for Zone 1, and under 10 hours per year for Zone 2, but these are interpretive aids, not clauses written into IEC 60079-10-1 itself. The actual classification is done by a competent person following a documented area classification study.
IEC 60079-10-2 mirrors the gas zone logic for combustible dust clouds:
Dust hazards also depend heavily on layer buildup, not just clouds. A thin dust layer on a hot motor or bearing housing can smolder and eventually flash, which is one reason dust prone equipment needs the same rigorous condition monitoring plants already apply to rotating assets, from bearing failure modes to routine vibration and thermal checks.
NFPA 70 (the National Electrical Code) historically classifies hazardous locations by Class and Division rather than Zone, though NEC Article 505 permits the Zone system as an alternative for Class I (gas) locations, and Article 506 permits it for Class II and III (dust and fiber) locations, in the US.
| Class | Hazard |
|---|---|
| Class I | Flammable gases, vapors, or liquids capable of forming ignitable mixtures |
| Class II | Combustible dust |
| Class III | Ignitable fibers or flyings, not normally airborne in explosive concentrations |
| Division | Meaning |
|---|---|
| Division 1 | Hazardous concentrations exist under normal operating conditions, or frequently due to repair, maintenance, or equipment breakdown |
| Division 2 | Hazardous concentrations exist only under abnormal conditions, such as a containment failure, and are otherwise not expected |
Roughly, Division 1 aligns with Zones 0 and 1, and Division 2 aligns with Zone 2, but the two systems are not calculated the same way and equipment listed under one is not automatically valid under the other without a documented cross reference. The NEC does not allow mixing both systems within the same location.
Not all flammable gases behave the same under a spark. IEC 60079-0 groups them by ignition characteristics such as minimum ignition energy:
Equipment rated IIC can be used anywhere IIB or IIA is required, since IIC is the superset; the reverse is not true. The NEC uses its own Group A/B/C/D letters (Group A is acetylene, Group D is propane equivalent), which map roughly to IIC, IIC, IIB, and IIA respectively, but the letter order does not track severity the same way it does in the IEC system, a common source of costly mis-specification. For dust, IEC 60079-0 defines Group IIIA (combustible flyings, particles above roughly 500 micrometers), IIIB (non-conductive dust, resistivity above 10 ohm-meters), and IIIC (conductive dust, resistivity at or below 10 ohm-meters).
Equipment installed in a hazardous area must never reach a surface temperature that could auto-ignite the surrounding atmosphere, even under a single fault. IEC 60079-0 defines six temperature classes by maximum permitted surface temperature:
| Class | Max surface temp |
|---|---|
| T1 | 450°C |
| T2 | 300°C |
| T3 | 200°C |
| T4 | 135°C |
| T5 | 100°C |
| T6 | 85°C |
The required T-class is set by the auto-ignition temperature of the most hazardous substance expected in that zone, and the equipment's marked T-class must stay comfortably below it. Motors running near a marginal T-class rating deserve the same scrutiny given to motor insulation classes and thermal limits, since winding heat and enclosure surface temperature are closely linked.
IEC and ATEX also assign an Equipment Protection Level (EPL): Ga, Gb, Gc for gas atmospheres and Da, Db, Dc for dust, corresponding respectively to Zones 0, 1, 2 and 20, 21, 22. Ga and Da equipment must remain safe with two independent faults, Gb and Db with one fault, and Gc and Dc with no faults assumed beyond normal operation. Selecting equipment correctly means matching zone, gas or dust group, and temperature class simultaneously, then confirming it on the equipment's certification marking before it goes anywhere near the line.
Fabrico reads machine condition and OEE directly from the line and auto-routes a work order the moment a loss is detected, catching early heat, vibration, or seal issues with computer vision before they become the kind of failure that turns a classified area into an incident. It is EU-built with EU data residency and carries ISO 27001, ISO 20000-1, and ISO 9001. Book a Fabrico demo.
ATEX (Directive 2014/34/EU) is a legal requirement for equipment placed on the EU market. IECEx is a voluntary international certification scheme accepted in many countries outside the EU. Both use the same underlying IEC 60079 technical standards, so an IECEx certificate typically supports an ATEX application and vice versa.
Not automatically. The NEC permits either system in the US, but equipment certified under one scheme needs a documented equivalency or separate listing before it can be installed under the other, and the underlying test methods and marking schemes differ.
The zone tells you how often an explosive atmosphere is present, the gas group tells you how easily that specific gas ignites. Equipment rated for the right zone but the wrong gas group, for example IIA-only equipment installed where hydrogen (IIC) is present, is not compliant even though the zone number matches.
A documented area classification study performed by a competent person, following IEC 60079-10-1 or 10-2, based on the release source, ventilation, and layout. It is not a generic lookup table; identical equipment in different buildings can be assigned different zones.
Zakažite sastanak KSNUMKS-to-KSNUMKS sa našim stručnjacima ili se direktno upišite u naš besplatni plan.
Nije potrebna kreditna kartica!
Login
Blog