Switchgear Maintenance: Inspection, Testing and Safety is the planned programme of inspection, cleaning, testing and repair that keeps medium-voltage (MV) and low-voltage (LV) switchgear, its circuit breakers, busbars, disconnectors and protection relays, operating safely and reliably. Switchgear rarely fails gradually in an obvious way. It sits energised for years, then fails suddenly at the worst moment: a loose connection overheats, insulation tracks, or a mechanism seizes during a fault. Structured maintenance turns those hidden defects into scheduled findings.
A switchboard carries continuous load current and must interrupt fault current on demand. Two failure families dominate. The first is thermal: bolted joints and contacts develop resistance, heat up, oxidise further and eventually melt or ignite. The second is dielectric: contamination, moisture and ageing degrade insulation until it tracks or flashes over. Both develop slowly and both are detectable long before failure. The maintenance job is to measure the early signals, connection temperature, contact resistance, insulation resistance and partial discharge, and act while the asset is still healthy.
A complete programme layers online (energised) checks against periodic offline work during a shutdown. The table below maps the main tasks to typical intervals and the failure mode each one detects. Intervals are a starting point; adjust them to load, environment, duty cycle and manufacturer guidance.
| Task | Typical interval | What it catches |
|---|---|---|
| Visual inspection, cleaning, cubicle checks | Monthly to quarterly | Dust, moisture ingress, corrosion, discoloured joints, oil or SF6 leaks |
| Infrared thermography of joints and connections (online) | 6 to 12 months | Loose or high-resistance connections, overloaded circuits, unbalanced phases |
| Contact-resistance (micro-ohm) test on breakers and busbars | 1 to 3 years | Eroded or misaligned contacts, degraded bolted joints |
| Insulation-resistance test with a megohmmeter | 1 to 3 years | Moisture, contamination, insulation ageing and tracking |
| Partial-discharge survey on MV assemblies | Annual (or continuous) | Voids, surface tracking, incipient insulation breakdown |
| Operating-mechanism clean, inspect and lubricate | 1 to 3 years or by operations count | Sluggish or failed tripping and closing, worn springs and latches |
| Protection-relay and trip-circuit test | 1 to 3 years | Mis-set, drifted or failed protection; broken trip wiring |
Thermography is the highest-value online check because it needs no outage. Scan the switchboard under meaningful load, ideally above 40 percent of rated current, so real hot spots appear. Compare each connection against the same phase on adjacent circuits and against ambient. A joint running tens of degrees above its neighbours is a loose or corroded connection heading for failure. Record emissivity, load at the time of scan and reflected temperature so results are comparable year to year. Follow up every anomaly with a torque check and, where possible, a contact-resistance measurement during the next outage.
Contact-resistance testing uses a micro-ohmmeter that injects a high DC current, commonly 100 A or more, across a closed breaker or a bolted joint and measures the millivolt drop to give resistance in micro-ohms. Rising values across successive tests, or a large spread between phases, reveal contact erosion or joint degradation long before thermography would flag them. This work is central to circuit breaker testing and belongs in every breaker overhaul.
Insulation-resistance testing applies a DC test voltage with a megohmmeter (typically 500 V or 1 kV on LV, 2.5 kV to 5 kV on MV) between phases and to earth. A polarisation index, the 10-minute reading divided by the 1-minute reading, distinguishes clean, dry insulation from contaminated or wet insulation. On critical MV switchgear, add partial discharge testing to detect internal voids and surface tracking that a steady-state insulation test can miss.
A breaker that cannot move when commanded is as dangerous as one with bad contacts. Clean old, hardened grease from the operating mechanism and relubricate with the manufacturer-specified lubricant; ordinary greases stiffen and cause slow or failed operation. Exercise racking mechanisms, check spring charging, and verify close and trip timing where equipment allows. On the control side, inspect terminations, confirm trip-circuit supervision is healthy, and functionally test protection relays and interlocks so a real fault is cleared correctly.
Working on or near switchgear exposes people to shock and to arc flash, the sudden release of energy from a fault that can reach thousands of degrees and generate a destructive pressure wave. The primary control is de-energising: isolate, lock out and tag out, then test dead and apply earths before touching conductors. Where a task must be done live, it requires a documented risk assessment, an established boundary, and arc-rated PPE selected for the calculated incident energy. Keep an up-to-date arc-flash study and clear labels so crews know the hazard before they open a door.
Individual readings matter less than their trend. Trending contact resistance, insulation resistance, polarisation index and hot-spot temperatures over time shows whether an asset is stable, drifting, or accelerating toward failure. That evidence drives the replace-or-refurbish call: a breaker with rising contact resistance and a sluggish mechanism may justify refurbishment, while an assembly with active partial discharge and obsolete parts is a replacement candidate. A CMMS such as Fabrico ties inspections, test results and work orders to each asset so trends are visible and decisions rest on history rather than guesswork. Book a Fabrico demo to see condition data drive maintenance planning.
Do visual checks and thermography every 6 to 12 months while energised, and offline testing (contact resistance, insulation resistance, mechanism service and relay testing) every 1 to 3 years. Shorten intervals for heavy duty, high load or harsh, humid or dusty environments.
Contact-resistance testing measures the resistance of the current-carrying path, contacts and bolted joints, in micro-ohms to catch erosion and loose connections. Insulation-resistance testing measures resistance between conductors and earth in megohms to catch moisture, contamination and insulation ageing. Both are needed.
Partly. Infrared thermography, partial-discharge surveys and visual inspection are done while energised and catch most thermal and dielectric defects early. Contact-resistance testing, insulation testing and mechanism service require the equipment to be safely isolated and proven dead.
An arcing fault releases intense heat and a pressure wave in milliseconds, causing severe burns and injury even from a distance. The safest control is to de-energise and prove dead before work. When live work is unavoidable, it demands a risk assessment, defined boundaries and correctly rated arc PPE.
Zakažite sastanak KSNUMKS-to-KSNUMKS sa našim stručnjacima ili se direktno upišite u naš besplatni plan.
Nije potrebna kreditna kartica!
Login
Blog