Air Handling Units (AHU): Components, Maintenance and Efficiency is a guide to the HVAC assembly that conditions and moves air through a building or process space, and to the maintenance that keeps it clean, efficient and reliable. An AHU is a cased set of sections that filter, heat, cool, humidify and move air, usually distributing it through ductwork to occupied or controlled zones. Because it runs continuously and touches both energy cost and air quality, it rewards disciplined preventive maintenance more than almost any other building asset.
An AHU draws in outdoor air, mixes it with return air, conditions it to a setpoint and delivers it at a controlled temperature, humidity and flow rate. It is the air-side terminus of a larger plant. The cooling coil is fed by chilled water from a chiller or by direct expansion refrigerant, and the heat rejected from that chiller is sent to a cooling tower or condenser. The AHU therefore never works in isolation. A fouled coil or a stuck damper shows up downstream as higher pumping load, longer chiller run hours and lost comfort control.
A typical built-up AHU is a train of sections, each with its own failure modes:
Filters are the single most frequent maintenance item. The correct trigger for a filter change is differential pressure across the bank, not a calendar date. A manometer or a differential-pressure switch reads the pressure drop, and the filter is replaced when it reaches the final resistance set by the manufacturer. Changing too early wastes media and labour; changing too late starves the fan, raises energy use and can collapse the media into the airstream. Modern filter selection follows ISO 16890, which classifies media by ISO Coarse, ISO ePM10, ISO ePM2.5 and ISO ePM1 efficiency and replaced the older EN 779 G and F grades.
Coil fouling is the quiet efficiency killer. A film of dust, biofilm or scale on the fins raises air-side pressure drop and cuts heat transfer, so the coil delivers less capacity while the fan and pump work harder. Coils are cleaned with soft brushing, compressed air or approved coil cleaner, always fin-parallel to avoid bending the aluminium. The same fouling logic that governs coils governs the wider plant, so it is worth understanding heat exchanger fouling as a general reliability problem. The condensate pan and drain trap must stay clear and biologically clean, because a blocked drain floods the pan, promotes microbial growth and can carry water into the duct. Fans need belt tension and alignment checks, bearing lubrication on schedule and vibration monitoring to catch imbalance or wear early.
| Component | Key maintenance task | Consequence if neglected |
|---|---|---|
| Filter bank | Track differential pressure; replace at final resistance | Reduced airflow, higher fan energy, bypass leakage |
| Cooling coil | Clean fins; keep face velocity in the 2.0 to 2.5 m/s range | Lost capacity, higher chiller load, moisture carryover |
| Condensate pan and trap | Clear drain; clean pan; verify trap seal | Overflow, microbial growth, water in ductwork |
| Supply and return fan | Belt tension, alignment, bearing lube, vibration check | Belt loss, bearing failure, unplanned downtime |
| Dampers and actuators | Stroke test linkage; confirm full open and close | No free cooling, poor fresh-air control, energy waste |
| Humidifier | Descale; check nozzles or steam distribution | Poor humidity control, mineral fouling, hygiene risk |
Every added pascal of resistance costs fan energy, and fan power rises steeply with flow and pressure. A clogged filter or a fouled coil forces the fan to work against higher static pressure, so kilowatt draw climbs even before comfort suffers. On the water side, a fouled coil transfers less heat, so chilled-water flow and chiller run hours increase to hold setpoint. That is why AHU condition is tied directly to plant efficiency and to chiller maintenance. The rejected heat then loads the tower, so tower cleanliness and water treatment, covered under cooling tower maintenance, close the loop. Clean filters, clean coils and free dampers are among the cheapest energy savings available in any building.
A defensible AHU program schedules filter checks by differential pressure, coil inspection and cleaning seasonally, drain and pan hygiene monthly in cooling season, fan belt and bearing checks quarterly, and full damper and actuator stroke tests before each heating and cooling changeover. Recording pressure drops, motor amps and vibration over time turns scattered tasks into a trend you can act on before a failure. A CMMS such as Fabrico can hold the asset register, trigger condition-based tasks and store the readings that reveal fouling early. Book a Fabrico demo to see how AHU schedules and readings sit alongside the rest of your plant.
By condition, not calendar. Replace filters when the measured differential pressure across the bank reaches the manufacturer's final resistance. Continuous monitoring of the pressure drop gives the true signal, while typical intervals only estimate it.
Fouling adds air-side pressure drop and lowers heat transfer at the same time. The fan uses more energy to push air through, and the chiller runs longer to hold the setpoint, so one dirty coil raises both air-side and water-side energy use.
Biofilm, dust washed off the coil and a failed or dry trap seal are the usual causes. A blocked drain floods the pan, encourages microbial growth and can carry water into the duct, so the pan and trap need routine cleaning through the cooling season.
Around 2.0 to 2.5 m/s is common. Above about 2.5 m/s the risk of condensate droplets being stripped off the fins and carried downstream rises, which is why a moisture eliminator is often fitted at higher velocities. Design and commissioning should confirm the actual face velocity.
Zakažite sastanak KSNUMKS-to-KSNUMKS sa našim stručnjacima ili se direktno upišite u naš besplatni plan.
Nije potrebna kreditna kartica!
Login
Blog