Labyrinth Seals: Non-Contact Sealing for Shafts and Bearings

A labyrinth seal forces a leaking fluid through interlocking teeth and chambers, dropping pressure in stages so leakage falls to an acceptable level rather than being eliminated outright.

Because the rotor and stator never touch, labyrinth seals avoid the friction, heat and wear that limit contact seals, making them the standard choice wherever shaft speeds are high, seal life must be long, and a small, controlled leak is acceptable.

How the Tortuous Path Reduces Leakage

A labyrinth seal consists of thin radial fins, or teeth, machined onto the rotating shaft or the stationary housing, facing a surface on the opposite member with a small radial clearance.

Each tooth forces fluid through a narrow gap into a slightly larger chamber, where it expands and loses velocity and pressure, converting pressure energy into turbulent heat.

Repeating this cycle across many teeth drops the pressure differential in small increments, so the flow escaping the last tooth is only a fraction of what a single orifice of the same clearance would pass.

Leakage is never fully stopped, since the seal relies on a running clearance rather than a rubbing interface. Design leakage rates are set by tooth count, radial clearance, chamber geometry and pressure differential, and are accepted as a controlled, predictable loss rather than a fault condition.

Non-Contact Operation and High-Speed Suitability

With no rubbing contact, labyrinth seals generate negligible frictional heat and consume little to no shaft power, an advantage on large turbomachinery where seal drag would otherwise be a measurable efficiency loss. There is no wear-driven end of life in normal operation, so service life tracks the machine's mechanical condition rather than a wear surface. This makes labyrinth seals well suited to:

• Very high surface speeds, beyond what contact seals tolerate without rapid wear
• High-temperature service, where elastomer contact seals would degrade
• Fluids that are poor lubricants, since no face lubrication is required
• Continuous operation where planned seal replacement is impractical

The trade-off: clearance-based sealing is leakier than a properly functioning contact seal, and performance is sensitive to rotor position, thermal growth and any rub event that alters the running clearance. A worn seal that forces a stop is unplanned downtime, so record which machine and which shift it hit.

Typical Applications: Turbines, Compressors and Bearing Isolators

Labyrinth seals are the default internal seal on steam and gas turbines, controlling leakage between stages and at shaft end glands, tolerating high speeds and hot, dirty process gas that would foul a contact seal. In centrifugal compressors, labyrinth seals, sometimes paired with dry gas seals, are used at balance drums and interstage locations to manage recirculation and axial thrust.

A second major use is as a bearing isolator: a compact labyrinth device fitted at the bearing housing end cap, in place of a conventional lip seal. Its job is to keep dust, wash-down water and moisture out of the housing while keeping lubricant in, not to contain a pressurized fluid.

Many isolators pair a labyrinth path with a rotating O-ring or a drainage groove that channels moisture back out before it reaches the bearing.

Labyrinth Seals versus Contact Seals

The choice between a labyrinth seal and a contact seal such as a mechanical seal or gland packing comes down to acceptable leakage versus tolerable wear, friction and maintenance.

Design and Selection Factors

Selecting a labyrinth seal involves several variables:

• Radial clearance: tighter clearance cuts leakage but raises rub risk during transients such as thermal growth, unbalance or shaft misalignment
• Tooth count and geometry: straight, stepped and interlocking patterns trade manufacturing cost against sealing effectiveness for a given axial length
• Fluid state: liquid, gas or two-phase flow behaves differently through the path, and gas seals are more prone to swirl-induced instability at high pressure ratios
• Abradable linings: a sacrificial stator lining lets rotor teeth cut a close-fitting groove on first contact without damage, self-optimizing clearance at commissioning

Monitoring and Maintenance Considerations

Because labyrinth seals have no wear component to inspect on a fixed interval, condition monitoring relies on indirect indicators: a rising leakage rate, a drop in stage efficiency, bearing contamination, or vibration severity readings consistent with a rotor rub.

Tracking these trends beats a calendar-based replacement policy, since the seal does not degrade on a predictable schedule the way a packing set or seal face does. Logging leakage, lubricant condition and rub events against the asset in a CMMS lets a reliability team catch a slow clearance drift before it causes a bearing failure.

Read how Fabrico tracks downtime to see this history tracked against the asset record.

Fabrico is software for OEE, downtime tracking and maintenance. We do not sell parts or repair services.

Frequently Asked Questions

Do labyrinth seals stop leakage completely?

No. They restrict leakage to a low, predictable rate by dropping pressure across a series of clearances, not by achieving zero leakage. Some flow always passes through the clearance.

Why are labyrinth seals preferred on turbines and high-speed compressors?

They generate minimal friction and heat, with no face or packing wear, so they operate reliably at speeds and temperatures that would destroy a contact seal.

What is a bearing isolator and how does it differ from a shaft seal?

A bearing isolator is a compact labyrinth device fitted at a bearing housing end cap. It keeps contamination out and lubricant in, rather than containing pressurized process fluid, and typically replaces a lip seal.

Can a labyrinth seal fail?

Yes, though not by wear the way a contact seal wears. A rotor rub from misalignment or thermal growth can open the clearance or damage teeth, and erosion from an abrasive fluid can enlarge the gap, raising leakage above design.