Statistical Process Control (SPC): Acting on Signals, Not Noise
Key takeaways
- Statistical process control (SPC) uses control charts to tell the difference between normal, expected variation and a real change that needs action.
- The central skill is restraint: reacting to every small wiggle ("tampering") makes a stable process worse. SPC tells you when not to act, which is most of the time.
- Common-cause variation is the natural noise of a stable process; special-cause variation is a signal that something specific changed. Only special causes warrant investigation.
- Control limits are not specification limits. Control limits describe what the process actually does; spec limits describe what the customer wants. Confusing them is the most common SPC error.
What SPC is
Every process varies. Two parts off the same machine are never identical to the micron. Statistical process control is the method for deciding whether a given amount of variation is just the process being itself, or a sign that something has genuinely changed and needs attention. It does this with a control chart: measurements plotted over time, with statistically derived limits.
The goal is not zero variation, which is impossible. The goal is a process that is stable and predictable, so that when it does shift, you notice quickly and for the right reason.
Common cause versus special cause
This distinction is the heart of SPC:
- Common-cause variation is the inherent noise of a stable process. It is always present and is not a problem to chase point by point.
- Special-cause variation is a signal: a point outside the control limits or a non-random pattern. Something specific changed (a tool wore, a material lot differed, a setting moved), and it is worth investigating with root cause analysis.
Treating common cause as special (reacting to every point) is tampering, and it provably increases variation. Treating special cause as common (ignoring real signals) lets defects through. SPC keeps you on the right side of that line.
Control limits versus spec limits
A frequent and costly confusion. Control limits are calculated from the process data and describe what the process naturally does. Specification limits come from the customer or design and describe what is acceptable.
A process can be in control (stable) yet still produce out-of-spec parts if it is not capable; conversely a process can be within spec but out of control. They answer different questions and must not be drawn on the chart as the same line.
Why it matters
SPC catches a drifting process before it produces a batch of scrap, which is the quality side of the same early-detection logic that drives OEE. It also stops well-meaning operators from over-adjusting a healthy process. Both protect the quality factor that feeds OEE and the loss accounting in production loss analysis.
Common mistakes
- Tampering. Adjusting after every point that is not perfectly on target. This adds variation rather than removing it.
- Confusing control and spec limits. Drawing customer tolerances as control limits defeats the chart's purpose.
- Charting everything. SPC is worth it on the few characteristics that matter, not on every measurable dimension.
How Fabrico fits
SPC governs the quality signal; Fabrico connects that signal to the rest of the picture.
Fabrico has no SPC charts. When your SPC chart shows a special cause, Fabrico shows the line's rejects, stops and OEE for the same time, so you can see whether it coincided with a stop, a changeover, or a material change, and open a task to follow it up.
Fabrico is built in the EU, EU customers are hosted on AWS in Frankfurt, and Fabrico holds an ISO/IEC 27001 certificate. To connect quality signals to production reality, book a demo.
Related reading
Teams putting this into practice often review our roundup of the cost of poor quality.
To turn this into a tool decision, see our overview of the quality management software.
Frequently asked questions
What does statistical process control actually do?
It uses control charts to separate normal process variation from a genuine change. That tells you when to investigate (a special-cause signal) and, just as importantly, when to leave a stable process alone rather than over-adjusting it.
What is the difference between common and special cause variation?
Common cause is the inherent noise of a stable process and should not be chased point by point. Special cause is a signal that something specific changed and warrants investigation. Confusing the two leads either to tampering or to missed defects.
Are control limits the same as specification limits?
No. Control limits are calculated from the process and describe what it naturally does. Specification limits come from the customer and describe what is acceptable. A process can be in control yet out of spec, or in spec yet out of control; they are different things.
What is tampering in SPC?
Adjusting a stable process in response to normal common-cause variation, as if every off-target point were a problem. It is a well-documented mistake that increases variation rather than reducing it, which is why SPC emphasises acting only on real signals.
See how Fabrico unifies OEE and maintenance in one platform.
Request a demoRelated articles

Real Fabrico tiles, sample data.









