Menu
Book a demo
MDCplus Alternatives: 6 Options by the Job You Need Done

MDCplus Alternatives: 6 Options by the Job You Need Done

Six MDCplus alternatives for machine shops, sorted by data route and pricing model, with published prices, a decision matrix and a costed sample shift.
MDCplus Alternatives: 6 Options by the Job You Need Done

In short: pick by the job. Stay with MDCplus if machine data must stay inside a closed network. If you need alarms and part counts read from the CNC control, look at MachineMetrics; if operators will not key in reasons, Datanomix; if you need a clip-on sensor at a published monthly price, FourJaw; if you want a one-time purchase with data kept on site, Vorne XL. TEEPTRAK and Mingo Smart Factory cover guided sensor pilots and plant-wide cloud.

  • MDCplus itself is licensed per machine as a perpetual license and installed on your own server, per its FAQ.
  • Vendor facts come from each vendor's own pages, read on 14.11.2026 and linked in place.

A quote from MDCplus is a quote for a perpetual license per machine on a server you run. Before signing it, three questions sort the other options: how the machine state gets in, who names the cause of a stop, and what the system costs over five years. Six MDCplus alternatives for a machine shop or discrete plant go through those questions below. Fabrico sits outside the six and gets one short section after the checks.

Key takeaways

  • The six options differ most in the data route: the CNC control, a clamp on the power cable, a wired sensor, or a person at a tablet.
  • MDCplus sells a perpetual license with support at 10% of project value a year; four alternatives sell by subscription and one sells a device at a one-time cost.
  • Published figures exist for Vorne XL (USD 4,490 to USD 4,990 per device) and FourJaw (GBP 72.00 to GBP 180.00 per machine per month), both accessed 14.11.2026; the rest quote on request.
  • In the sample shift below, 140 lost machine minutes cost EUR 280.00 at a sample rate of EUR 120 per machine hour, and 28 of them trace to one tool-life alarm.

What MDCplus is, from its own pages

MDCplus, with an office in Helsinki per its company page, calls itself "machine monitoring and OEE software for manufacturers" in its FAQ. As of 14.11.2026 its pages say:

  • Connection. The FAQ names the main CNC control brands plus PLCs and legacy machines, and says "the connection is read-only". The public machine connectivity checker needs no account: pick a control and it returns the recommended protocol, the connection method and the expected complexity. For a FANUC 31i it shows FOCAS 2 over Ethernet, rated "Standard".
  • Modules. The FAQ lists "real-time machine monitoring, power consumption monitoring, computerized maintenance, vibration monitoring and diagnostics, DNC and NC program management, and production control MES system".
  • Operators. The product overview describes a panel that is "a web application designed for interaction between the machine operator and the MDCplus".
  • Where it runs. The FAQ says MDCplus is "installed on premise, on your own server, and works fully inside a closed network with no internet access". The product overview also describes a cloud option with data "stored on the Microsoft Azure Cloud Server", and the homepage says "Available on site and in the cloud." Ask which of the two your quote covers.
  • Price. MDCplus: no public price; quote on request (checked 14.11.2026); the FAQ does publish the model: "MDCplus is a one-time purchase", a perpetual license per machine that "includes implementation and the server license", with technical support "priced at 10% of the project value annual". The homepage adds "ask for free trial".

No review score appears here for MDCplus: the review sites tried on 14.11.2026 could not be read. For background on the category, see machine data collection (MDC) and CNC machine monitoring.

Six MDCplus alternatives, ordered by how the data gets in

The order follows the data route, from the CNC control outward to sensors, a device at the machine and a plant platform. Read the two or three entries that match your machines.

MachineMetrics: controller data and operator tablets, by subscription

The MachineMetrics machine monitoring page describes reading the CNC control directly, plus "digital and analog I/O for machines without a standard connectivity option". It monitors "machine conditions (faults, status, tool utilization)", and downtime reasons "can be auto classified or indicated by the operator with touch screen tablet interfaces mounted at the machine tool". Machine data is "encrypted and stored in the cloud". A public developer site documents GraphQL and REST APIs and webhooks for whoever owns the ERP link.

Price. MachineMetrics: no public price; quote on request (checked 14.11.2026); three plans, Core Platform, Intelligent MES and Enterprise, sit on a pricing page that calls the model "a true SaaS subscription model" and says "the more machines you connect, the less it costs per machine". The same page describes an "ISO 27001 certified cloud-based system".

Look at it if you want what the control knows, alarms and programs included, and a cloud subscription suits your IT policy. The MachineMetrics alternatives page covers the reverse question.

Datanomix: job scoring with no operator entry

Datanomix builds its pitch on one phrase from its homepage: "No Operator Input™ Required". The production monitoring page says "Datanomix matches live machine programs to those jobs", and "Production scores for every job are displayed on smart TVs on the shop floor". The homepage also lists a G-Code Cloud and DNC product described as "Fully CMMC 2.0 Compliant".

Price. Datanomix: no public price; quote on request (checked 14.11.2026); the production monitoring page gives the model as "priced per machine per year, not per user". Instead of a free trial it runs a pilot program, under the heading "Free Trials Waste Time. Our Pilot Delivers Outcomes."

User signal. App Store, Datanomix iOS app: 5.0 out of 5 from 4 ratings, read 14.11.2026 (listing). Four ratings are too few to weigh.

Look at it if operator entry is what sank your last attempt and most of your machines are CNC. See also Datanomix alternatives.

FourJaw: a clip-on sensor at a published monthly price

FourJaw's hardware page describes the route in three lines: "Clip the sensors to the machine's power cables.", "No connection to the machine controller required." and "Data is securely hosted in the cloud." The reason comes from a person: "Tablet wakes up when productivity drops, ensuring no downtime goes uncategorised."

Price. The FourJaw pricing page publishes figures in GBP (accessed 14.11.2026). Standard is GBP 90.00 per machine per month billed monthly, or GBP 72.00 billed annually. Pro is GBP 180.00, or GBP 144.00 billed annually. "A five-machine minimum applies to all plans". Its FAQ adds, for Standard, a one-time fee of GBP 200 for the MachineLink device; Pro states "All Hardware Included in the Plan".

Look at it if the shop is a mix of old, manual and CNC machines, nobody wants to open a control cabinet, and the budget has to be known before the first call. More options of this kind are on the FourJaw alternatives page.

TEEPTRAK: plug-in sensors and a guided pilot

The TEEPTRAK homepage describes plug-and-play sensors with "No PLC work, no production stop." and puts the cause with the operator: "Operators qualify causes in two taps."

Price. TEEPTRAK: no public price; quote on request (checked 14.11.2026); the homepage offers "Start your 90-Day Guided Pilot" on one line, with the words "A TEEPTRAK engineer sets up your pilot line. No commitment."

Look at it if you want a sensor route without controller work and a supervised pilot that ends in a yes or no.

Vorne XL: a one-time-cost device with data kept on site

Vorne sells a device. The Vorne homepage says: "Wire one or two sensor inputs from an existing machine photo-eye, relay, proximity switch, or encoder to XL." A barcode scanner plugged into XL lets operators "scan down time reasons", and the XL scoreboard shows the state in real time. The XL page says "Your data stored securely behind your firewall."; the homepage calls the XL Enterprise cloud part "entirely optional".

Price. The Vorne models page publishes figures in USD (accessed 14.11.2026): XL810-1 at USD 4,490, XL HD+ at USD 4,690 and XL Touch at USD 4,990, "for single unit quantities, volume discounts are available". It adds "no recurring costs" and invites plants to try XL "free for 90 days".

User signal. App Store, XL Sidekick app: 5.0 out of 5 from 4 ratings, read 14.11.2026 (listing), again too small a sample to weigh.

Look at it if the job is one count and one scoreboard per machine, bought once, with data on a device inside the plant. Related reading: Fabrico vs Vorne XL and Mingo vs Vorne XL.

Mingo Smart Factory: a cloud platform with a managed ERP link

A line across the top of mingosmartfactory.com reads "Mingo Smart Factory is Now a Nulogy Company"; Nulogy confirms the deal in its own press release. How Mingo Works lists "Hardware to connect existing controllers or PLCs" and "Sensors or wireless nodes to retrofit machines to collect data", and says "We run our software in a dedicated public cloud (AWS) environment." The managed integration page describes the ERP side: "Import parts, production data and schedule from your ERP."

Price. Mingo Smart Factory: no public price; quote on request (checked 14.11.2026); Growth, Scale and Enterprise plans appear on its pricing page, with three cost components: "Licensing per site per year", connection hardware and implementation fees.

Look at it if the plant has presses, moulding or assembly beside the CNC machines and wants production counts posted to the ERP as a service. See Mingo Smart Factory alternatives.

Four routes from machine to screenController interfaceMDCplus, MachineMetrics, DatanomixClamp on the power cableFourJawSensor wired to a device or nodeVorne XL, TEEPTRAK, MingoOperator tablet or panelA person names the cause of the stopAs each vendor's pages describe, 14.11.2026
The route decides what arrives without a person: a control gives states, programs and alarms, a power clamp gives load, a wired sensor gives counts.

What each vendor publishes about price

Every cell is from the vendor's own page on 14.11.2026, in the currency that page uses. Nothing is converted and nothing is estimated.

VendorHow it charges (its page)Published figure
MDCplusPerpetual license per machine; support at 10% of project value a yearno public price; quote on request (checked 14.11.2026)
MachineMetricsSubscription, volume based per machineno public price; quote on request (checked 14.11.2026)
DatanomixPer machine per year, not per userno public price; quote on request (checked 14.11.2026)
FourJawPer machine per month, five-machine minimumGBP 72.00 to GBP 180.00 per machine per month; GBP 200 one-time device fee on Standard (accessed 14.11.2026)
TEEPTRAKGuided pilot offered on one lineno public price; quote on request (checked 14.11.2026)
Vorne XLOne-time cost per device, no recurring costsUSD 4,490 to USD 4,990 per device, single-unit list (accessed 14.11.2026)
Mingo Smart FactoryLicense per site per year, plus hardware and implementationno public price; quote on request (checked 14.11.2026)

The three shapes do not compare on a first-year number. A perpetual license front-loads the spend and leaves support as the yearly line. A subscription spreads it and never stops. A device is bought once per machine. Ask every vendor for a five-year total on one machine list, with hardware, tablets, support and services included, and compare those.

Decision flowchart for MDCplus alternatives: seven buyer situations, each pointing to the vendor to look at first
Start from the first job, then prove the choice on the same two machines. No sample data. Sources: mdcplus.fi, machinemetrics.com, datanomix.io, fourjaw.com, teeptrak.com, vorne.com and mingosmartfactory.com, read 14.11.2026.
Text version of this infographic
  • Data must stay in a closed network and the license should be yours to keep: MDCplus (stay).
  • You want alarms, programs and part counts read from the CNC control: MachineMetrics.
  • Operators will not key in reasons and you want a score per job: Datanomix.
  • Mixed old and manual machines, a clamp on the power cable, a published monthly price: FourJaw.
  • Plug-in sensors and a guided pilot with a decision date: TEEPTRAK.
  • One count, one scoreboard, a one-time purchase, data on a device on site: Vorne XL.
  • Several work centres in the cloud and an ERP link run as a service: Mingo Smart Factory.
  • Then prove it in the pilot: the same two machines for each vendor, one shift counted by hand as the reference, a five-year total in writing for the same machine list.

Decision matrix: MDCplus or an alternative for your plant

Each row is a situation, the option whose own page speaks to it, and a test that settles it on the floor. Rows where all seven answer alike were left out; they are listed under the table.

If this is youLook first atWhy (vendor page)Prove it in the pilot by
Machine data must stay in a closed network, and you want to own the licenseMDCplus (stay)FAQ: "works fully inside a closed network with no internet access"; perpetual license per machineRunning the pilot server with the internet link unplugged, then asking for the quote split by module
Monitoring, maintenance, DNC and vibration should sit in one systemMDCplus (stay)FAQ: modules include "computerized maintenance" and "DNC and NC program management"Sending one NC program and closing one maintenance job in the pilot, not in a slide
You want alarms, programs and part counts from the control, in the cloudMachineMetricsMachine monitoring: "machine conditions (faults, status, tool utilization)"Matching one day of control part counts against the operator's tally sheet
Operators will not key in reasons; you want a score per jobDatanomixHomepage: "No Operator Input™ Required"Checking the part number on screen against the traveller on five jobs
Old, manual and CNC machines together; budget fixed before the first callFourJawHardware: "No connection to the machine controller required."; pricing: GBP 72.00 to GBP 180.00 per machine per month (accessed 14.11.2026)Clamping one saw and one CNC, then timing run and idle with a stopwatch for an hour
You want a supervised pilot on one line that ends in a decisionTEEPTRAKHomepage: "A TEEPTRAK engineer sets up your pilot line. No commitment."Agreeing in writing, before the start, how the baseline is measured
One count and one scoreboard per machine, bought once, data on siteVorne XLModels page: USD 4,490 to USD 4,990 per device (accessed 14.11.2026), "no recurring costs"; XL page: "Your data stored securely behind your firewall."Wiring one sensor and reading the device count against the machine counter at shift end
Several work centre types, with counts posted to the ERP as a serviceMingo Smart FactoryManaged integration: "Import parts, production data and schedule from your ERP."Checking a day of ERP postings against the counters of two machines

Left out because they do not separate the seven: an OEE figure, alerts when a machine stops, a view on a wall screen, and some form of API or export. All seven describe these on their own pages, so they cannot decide the choice.

Worked example: a tool-life alarm at 14:20 on a twin-pallet machining centre

Sample data, made up for this page. No customer, no product screen. A horizontal machining centre with a FANUC 31i control cuts aluminium manifold blocks, one per pallet. Planned time is 560 minutes: a 10-hour shift less 40 minutes for breaks. The ideal cycle is 4 minutes a block, which makes 140 blocks possible.

At 14:20 the control raises a tool-life alarm on a drill and the spindle stops. The spare is not in the crib. The machine waits 28 minutes. Three of the tools, as their own pages describe them:

  • MDCplus. The connectivity checker gives this control a monitoring scope of "Status, program, alarms, counters, overrides and loads", so the alarm arrives from the control itself. The product overview says "Downtime reasons identified and classified" and that specialists "get automated notifications about accidents and unplanned downtime". The operator panel is where a person confirms what the tool crib did.
  • MachineMetrics. Its page says it monitors "machine conditions (faults, status, tool utilization)", so the fault is on the timeline. The reason "can be auto classified or indicated by the operator" on the tablet, and "a text or email notification can be sent" to whoever is off the floor.
  • FourJaw. The clamp sees the current drop when the spindle stops. The page says "Tablet wakes up when productivity drops", and the operator taps the reason. The record holds the 28 minutes and the operator's word for the cause; the alarm text stays on the control screen, since the route is the power cable.

All three hold the 28 minutes; what differs is how much of the cause arrives without a person. The rest of the shift log reads: setup and first-off 36 minutes, waiting at the pallet station 14, and 6 minutes with no reason yet. Stops total 84 minutes.

One shift, 560 planned minutesSample data, not a product screenRunning 476 minSetup and first-off, 36 minTool-life alarm, waiting for a tool, 28 minWaiting at the pallet station, 14 minNo reason yet, 6 minAvailability85.0%Performance90.8%Quality97.2%OEE, 105 of 140 blocks75.0%
Sample data. The 28 minute tool wait is the stop the three tools above would record in three different ways; the OEE arithmetic is the same in all of them.

The OEE arithmetic. Run time is 560 less 84, so 476 minutes: availability is 476 / 560 = 85.0%. In 476 minutes the ideal is 119 blocks; the machine made 108, so performance is 108 / 119 = 90.8%. Inspection scrapped 3, leaving 105 good: quality is 105 / 108 = 97.2%. OEE is 85.0% x 90.8% x 97.2% = 75.0%, the same as 105 good blocks of 140 possible. The OEE calculation guide shows the method.

The same shift in euros

The 35 missing blocks equal 140 machine minutes. The minute price is anchored to a sourced labour figure. For 2025, Eurostat gives industry, its highest-paying sector, EUR 40.3 an hour, with EU countries spanning EUR 12.0 to EUR 56.8 (accessed 14.11.2026). Take EUR 40.3 for the operator, add a sample EUR 79.7 for machine, tooling, floor space and overhead, and the sample rate is EUR 120 per machine hour, EUR 2.00 a minute. MDCplus's own machine hour rate calculator lands in the same order: its default example ends with "a productive hour costs $120" (accessed 14.11.2026).

Loss (sample data)Machine minutesPer shift (EUR)Per year (EUR)
Stops84168.0080,640
Slow cycles, 119 less 108 blocks4488.0042,240
Scrap, 3 blocks1224.0011,520
Total gap to ideal140280.00134,400

The year assumes two shifts a day on 20 days a month: 40 shifts a month, 480 a year. A month is EUR 11,200. The tool wait alone is 28 minutes, EUR 56.00 a shift; if it recurred on every shift it would be EUR 26,880 a year, which is the size of problem a spare-tool rule can remove. The total is a ceiling: no machining centre runs a year at its ideal cycle with no setups.

Three checks before you compare quotes

What the control can expose. A controller route is a cable on one machine and a project on the next. MDCplus's checker carries the note "Controller options must be confirmed before commissioning." on its Siemens row, and MachineMetrics lists UMATI among its protocols. umati states: "umati is based on OPC UA, which provides a communication framework between devices on the shop floor." (accessed 14.11.2026). Ask each machine builder which interface is enabled on your serial numbers before you price a controller route; the OPC UA and OEE guide explains what the interface carries.

Where the data may live. If you machine parts under US defence contracts, the place the data sits is a compliance question before it is a software one. NIST SP 800-171 Rev. 3, published May 2024, sets out "recommended security requirements for protecting the confidentiality of CUI" in non-federal systems (accessed 14.11.2026). MDCplus pitches its closed-network install at "defense and other critical production"; Datanomix and MachineMetrics state their own cloud credentials, quoted above. Take the data-location row of each quote to your compliance lead first. The edge vs cloud guide lists the questions IT tends to ask.

What monitoring leaves open. If the gap is why time is lost by order and shift, read MES vs machine monitoring before choosing by connector list.

Where Fabrico fits

Fabrico's product is cloud-hosted OEE software with light MES functions; the MES and OEE solution overview sets out the scope. It is not a CNC data collection suite: no DNC, NC program management or vibration diagnostics. Against the options above, it covers four things.

  • Signal. Fabrico reads run, stop and count from the machine's PLC; see the OPC UA and OEE guide.
  • Cause. A person at the machine picks the stop reason on a phone or tablet.
  • Stations with no signal. At a manual deburring, assembly or packing step, the camera add-on counts output. Where a camera covers the line, the video for the minute of a stop can be opened from the shift timeline; it is streamed on request and not stored.
  • Money. OEE, downtime and lost output are shown by line and shift, with losses priced from selling price and margin per product.

That makes it a fit where the plant is wider than its CNC machines and the question is which losses cost the most, in euros, across lines. A demo walks through it on a sample line.

What to do this week

  1. List the machines by route. For each one write the control and year, then run the CNC ones through the MDCplus connectivity checker.
  2. Write the three definitions. Planned time, ideal cycle per part, and how long a stop must last before it counts. Give every vendor the same sheet.
  3. Ask for a five-year total. Send one machine list to MDCplus and to the two alternatives that match your rows in the matrix. Ask for license or subscription, hardware, tablets, support and services over five years.
  4. Settle where data may live. Agree with IT and compliance on closed network, device on site or cloud, in writing, before a pilot.
  5. Count one shift by hand. Parts, stops and reasons on paper for two machines. That sheet is the reference the pilot has to match.
  6. Put your own rate in the table. Swap the EUR 120 sample for your machine hour rate, so the pilot result reads in money.

What MDCplus buyers ask next

What is MDCplus?

MDCplus is machine monitoring and OEE software from a company with an office in Helsinki. Its FAQ says it collects data from CNC machines, PLCs, robots and legacy equipment, is licensed per machine as a perpetual license and is installed on your own server. Its product overview also describes a cloud option hosted on Microsoft Azure.

Is MDCplus a subscription or a one-time purchase?

A one-time purchase, per its own FAQ as of 14.11.2026: a perpetual license per machine that includes implementation and the server license. Technical support is the recurring item, stated as 10% of the project value a year. The site lists no figure per machine, so the number comes by quote.

Which MDCplus alternatives publish their prices?

Two of the six on this page, as of 14.11.2026. Vorne lists its XL devices at USD 4,490 to USD 4,990 per unit as a one-time cost. FourJaw lists GBP 72.00 to GBP 180.00 per machine per month, with a five-machine minimum. MachineMetrics, Datanomix, TEEPTRAK and Mingo Smart Factory describe a pricing model and quote on request.

Which alternative works without a connection to the CNC control?

FourJaw's hardware page describes sensors clipped to the machine's power cables with no connection to the machine controller required. TEEPTRAK describes plug-and-play sensors with no PLC work, and Vorne XL takes one or two sensor inputs wired to the device.

Where does Fabrico fit among MDCplus alternatives?

Outside the six. Its product is cloud-hosted OEE software with light MES functions rather than a CNC data collection suite. Machine signals give run, stop and count, a person at the machine picks the stop reason on a phone or tablet, and each line and shift shows its losses priced in euros. Where a machine has no usable signal, a camera add-on counts output.

Want a machining cell or a packing line shown with its OEE, stop reasons and losses in euros? Book a demo.

Track OEE and downtime in real time
See where lines lose time
Book a live demo.
See where lines lose time
See where lines lose time

Real Fabrico tiles, sample data.

By clicking the Accept button, you are giving your consent to the use of cookies when accessing this website and utilizing our services. To learn more about how cookies are used and managed, please refer to our Privacy Policy and Cookies Declaration